The EMOD is based on the same rugged and practical design as the original Vltor Modstock  with specific features designed from lessons taken from the modern battlefield. The EMOD is about one inch longer than the original Modstock and with the rubber butt plate installed, is about a quarter of an inch longer than the CRANE SCB. The increased length of the EMOD is a major benefit when used on scoped rifles (SPR/DMR), as it increases the available comb for any given length of pull. The buttplate of the EMOD is slightly wider and longer at the toe than the regular M4 stock with a noticeable negative pitch, making transitions from the ready feel much more natural. The EMOD was given enough weight to help balance out the normally muzzle heavy feel associated with negative pitch buttstocks. FOR USE WITH MIL SPEC RECEIVER EXTENSION TUBES.

Our Price: each $119.65

In Stock

The EMOD is based on the same rugged and practical design as the original Vltor Modstock  with specific features designed from lessons taken from the modern battlefield. The EMOD is about one inch longer than the original Modstock and with the rubber butt plate installed, is about a quarter of an inch longer than the CRANE SCB. The increased length of the EMOD is a major benefit when used on scoped rifles (SPR/DMR), as it increases the available comb for any given length of pull. The buttplate of the EMOD is slightly wider and longer at the toe than the regular M4 stock with a noticeable negative pitch, making transitions from the ready feel much more natural. The EMOD was given enough weight to help balance out the normally muzzle heavy feel associated with negative pitch buttstocks. FOR MIL SPEC DIAMETER EXTENSION TUBES.

Our Price: each $119.65

In Stock

The EMOD is based on the same rugged and practical design as the original Vltor Modstock  with specific features designed from lessons taken from the modern battlefield. The EMOD is about one inch longer than the original Modstock and with the rubber butt plate installed, is about a quarter of an inch longer than the CRANE SCB. The increased length of the EMOD is a major benefit when used on scoped rifles (SPR/DMR), as it increases the available comb for any given length of pull. The buttplate of the EMOD is slightly wider and longer at the toe than the regular M4 stock with a noticeable negative pitch, making transitions from the ready feel much more natural. The EMOD was given enough weight to help balance out the normally muzzle heavy feel associated with negative pitch buttstocks. FOR USE WITH MIL SPEC RECEIVER EXTENSION TUBES. Kit includes our 6 position mil-spec buffer tube, castle nut, stock plate, carbine buffer and spring. 

Our Price: each $161.70

In Stock

The EMOD is based on the same rugged and practical design as the original Vltor Modstock  with specific features designed from lessons taken from the modern battlefield. The EMOD is about one inch longer than the original Modstock and with the rubber butt plate installed, is about a quarter of an inch longer than the CRANE SCB. The increased length of the EMOD is a major benefit when used on scoped rifles (SPR/DMR), as it increases the available comb for any given length of pull. The buttplate of the EMOD is slightly wider and longer at the toe than the regular M4 stock with a noticeable negative pitch, making transitions from the ready feel much more natural. The EMOD was given enough weight to help balance out the normally muzzle heavy feel associated with negative pitch buttstocks. FOR USE WITH MIL SPEC RECEIVER EXTENSION TUBES.  Kit includes our 6 position mil-spec buffer tube, castle nut, stock plate, carbine buffer and spring. 

Our Price: each $161.70

In Stock

In 2010 the original Modstock was upgraded to a new and improved version. This stock is appropriately named the “IMod”, short for Improved Modstock. Will fit on your Military Spec receiver extension.

The improvements of the IMod are as follows:

• Integral, but removable non-slip buttpad (color matched to stock components)
• Rolled/angled buttpad toe with wide traction area. This will assist in running the stock high on shoulder, making the IMod system more user friendly when using web-gear and/or body armor.
• Improved lock paddle, making it easier to operate and making the contact surface non-slip when operating the lever.
• Removed most sharp edges that may cause “snag points” to web-gear or other vital equipment.
• Improved strength throughout construction of the stock chassis. This will provide maximum strength during “Mortaring exercise” or unexpected impact.  

Our Price: each $94.95

In Stock

In 2010 the original Modstock was upgraded to a new and improved version. This stock is appropriately named the “IMod”, short for Improved Modstock. Will fit on your Military Spec receiver extension.

The improvements of the IMod are as follows:

• Integral, but removable non-slip buttpad (color matched to stock components)
• Rolled/angled buttpad toe with wide traction area. This will assist in running the stock high on shoulder, making the IMod system more user friendly when using web-gear and/or body armor.
• Improved lock paddle, making it easier to operate and making the contact surface non-slip when operating the lever.
• Removed most sharp edges that may cause “snag points” to web-gear or other vital equipment.
• Improved strength throughout construction of the stock chassis. This will provide maximum strength during “Mortaring exercise” or unexpected impact.  

Our Price: each $94.95

In Stock

In 2010 the original Modstock was upgraded to a new and improved version. This stock is appropriately named the “IMod”, short for Improved Modstock. Kit includes our 6 position mil-spec buffer tube, castle nut, stock plate, carbine buffer and spring. 

The improvements of the IMod are as follows:

• Integral, but removable non-slip buttpad (color matched to stock components)
• Rolled/angled buttpad toe with wide traction area. This will assist in running the stock high on shoulder, making the IMod system more user friendly when using web-gear and/or body armor.
• Improved lock paddle, making it easier to operate and making the contact surface non-slip when operating the lever.
• Removed most sharp edges that may cause “snag points” to web-gear or other vital equipment.
• Improved strength throughout construction of the stock chassis. This will provide maximum strength during “Mortaring exercise” or unexpected impact.  

Our Price: each $137.00

In Stock

In 2010 the original Modstock was upgraded to a new and improved version. This stock is appropriately named the “IMod”, short for Improved Modstock. Kit includes our 6 position mil-spec buffer tube, castle nut, stock plate, carbine buffer and spring. 

The improvements of the IMod are as follows:

• Integral, but removable non-slip buttpad (color matched to stock components)
• Rolled/angled buttpad toe with wide traction area. This will assist in running the stock high on shoulder, making the IMod system more user friendly when using web-gear and/or body armor.
• Improved lock paddle, making it easier to operate and making the contact surface non-slip when operating the lever.
• Removed most sharp edges that may cause “snag points” to web-gear or other vital equipment.
• Improved strength throughout construction of the stock chassis. This will provide maximum strength during “Mortaring exercise” or unexpected impact.  

Our Price: each $137.00

In Stock

The Vltor A5 tube has seven locking positions and is designed to work with a MilSpec diameter, lengthened collapsable stock, such as the Vltor Enhanced Modstock.

This Vltor A5 receiver extnsion stock kit includes a 7 position collapsible stock tube, buffer, buffer spring, castle nut & receiver end plate.

THESE PARTS ARE PART OF THE A5 RIFLE RECOIL SYSTEM. THESE PARTS ARE NOT THE SAME AS STANDARD CARBINE RECEIVER EXTENSIONS OR BUFFERS. ATTEMPTING TO USE ANY OF THESE PARTS WITH STANDARD CARBINE RECOIL SYSTEMS WILL RESULT IN DAMAGE TO THE FIREARM!

Our Price: each $104.00

In Stock

6oz Buffer

THESE PARTS ARE PART OF THE A5 RIFLE RECOIL SYSTEM. THESE PARTS ARE NOT THE SAME AS STANDARD CARBINE RECEIVER EXTENSIONS OR BUFFERS. ATTEMPTING TO USE ANY OF THESE PARTS WITH STANDARD CARBINE RECOIL SYSTEMS WILL RESULT IN DAMAGE TO THE FIREARM!

Our Price: each $47.45

In Stock

7oz Buffer

THESE PARTS ARE PART OF THE A5 RIFLE RECOIL SYSTEM. THESE PARTS ARE NOT THE SAME AS STANDARD CARBINE RECEIVER EXTENSIONS OR BUFFERS. ATTEMPTING TO USE ANY OF THESE PARTS WITH STANDARD CARBINE RECOIL SYSTEMS WILL RESULT IN DAMAGE TO THE FIREARM!

Our Price: each $56.95

In Stock